Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems

Harish Aryal

doi:doi:10.11648/j.ajset.20230802.14

| Peer-Reviewed

Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems

Harish Aryal

Published in American Journal of Science, Engineering and Technology (Volume 8, Issue 2)

Received: 16 April 2023 Accepted: 22 May 2023 Published: 31 May 2023

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

The project is about building an infrastructure for an open loop technique and implementing this technique to measure the reactivity worth of small samples. The reactivity samples are allowed to oscillate back and forth in the reactor system to cause perturbations and the corresponding reactor response is measured in the form of the transfer function. The transfer function obtained is used to determine stability characteristics along with other kinetic parameters such as delayed neutron fraction, prompt neutron lifetime, shutdown margins, and absolute power. This paper compares transfer functions for reactors like Neutron Radiography (NRAD) and Aerojet General Nuclear (AGN-201). The magnitude of the transfer function correlates with the reactivity of the sample that caused the perturbation. In addition, the transfer function allows one to determine whether the reactor is a stable system or not. In other words, the reactor’s response to the change in neutron population in the reactor can be easily described. Moreover, a transfer function measurement is useful to extract important kinetic parameters of the reactor system, such as instance prompt neutron generation lifetime, reactivity shutdown margin, absolute power, etc. The transfer function plots presented in the results section correlate the reactivity of the sample that caused perturbations. NRAD was found to have a higher break frequency than that AGN-201. This was an expected result since break frequency is inversely proportional to neutron generation time. With this relation, break frequency was found to be around 306 Hertz. So, the reactor cannot respond beyond this frequency but passes the low frequencies. The corresponding analysis and comparative transfer function plots using MATLAB for these two reactor systems are presented in the results section. Many reactivity measurements have been already in practice however if the transfer function technique can give reactivity measurements with similar or better precision and accuracy, it could be a great benefit. Moreover, this can be installed in those facilities where more complex systems cannot be incorporated easily.

Published in	American Journal of Science, Engineering and Technology (Volume 8, Issue 2)
DOI	10.11648/j.ajset.20230802.14
Page(s)	104-109
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2023. Published by Science Publishing Group

Keywords

Transfer Function, Radiograph, Reactivity, Shutdown, NRAD, AGN-201

References

[1]	Ahmad, S., Abdulraheem, K. K., Tolokonsky, A. O., & Ahmed, H. (2023). Active disturbance rejection control of pressurized water reactor. Annals of Nuclear Energy, 189. https://doi.org/10.1016/j.anucene.2023.109845
[2]	Ayazuddin, S. K., & Sari, S. A. A. (1984a). REACTOR TRANSFER FUNCTION MEASUREMENT AT PARR BY NEUTRON NOISE ANALYSIS.
[3]	Ayazuddin, S. K., & Sari, S. A. A. (1984b). REACTOR TRANSFER FUNCTION MEASUREMENT AT PARR BY NEUTRON NOISE ANALYSIS.
[4]	Baker, Benjamin Allen. Reactor Parameters for the ISU-AGN-201 Reactor. Pocatello, Idaho: Idaho State University, 2013.
[5]	Baker, Benjamin Allen. Comparison of Open Loop and Closed Loop Reactivity Measurement Technique on the ISU-AGN-201 Reactor. Pocatello, Idaho: Idaho State University, 2013.
[6]	Bläsius, C., Herb, J., Sievers, J., Knospe, A., Viebach, M., & Lange, C. (2022). Mechanical model for the motion of RPV internals affecting neutron flux noise. Annals of Nuclear Energy, 176. https://doi.org/10.1016/j.anucene.2022.109243
[7]	Bess, John D. et al. FreshCore Reload of the Neutron Radiography (NRAD) Reactor with Uranium (20) –Erbium -Zirconium-Hydride Fuel Department of Energy, Idaho National Laboratory, 2010.
[8]	Demazière, C., Rouchon, A., & Zoia, A. (2022). Understanding the neutron noise induced by fuel assembly vibrations in linear theory. Annals of Nuclear Energy, 175. https://doi.org/10.1016/j.anucene.2022.109169
[9]	Herb, J., Périn, Y., Yum, S., Mylonakis, A., Demazière, C., Vinai, P., Yu, M., Wingate, J., & Hursin, M. (2022). Sensitivity analysis in core diagnostics. Annals of Nuclear Energy, 178. https://doi.org/10.1016/j.anucene.2022.109350
[10]	Hetrick, David L. Dynamics of Nuclear Reactors. La Grange Park, Illinois: American Nuclear Society, 1993.
[11]	Hui, J., & Yuan, J. (2022). Adaptive second-order nonsingular terminal sliding mode power-level control for nuclear power plants. Nuclear Engineering and Technology, 54 (5), 1644–1651. https://doi.org/10.1016/j.net.2021.10.041
[12]	James J. Duderstadt, Louis J. Hamilton. Nuclear Reactor Analysis. s. l.: John Wiley & Sons, inc., 1976.
[13]	Kim, H., & Kim, J. (2023). Long-term prediction of safety parameters with uncertainty estimation in emergency situations at nuclear power plants. Nuclear Engineering and Technology. https://doi.org/10.1016/j.net.2023.01.026
[14]	Korbut, T., Kuzmin, A., Rudak, E., & Kravchenko, M. (2021). Transient analysis of a subcritical reactor core with a MOX-Fuel using the birth-and-death model. Nuclear Engineering and Technology, 53 (6), 1731–1735. https://doi.org/10.1016/j.net.2020.11.023
[15]	Lee, E. K., Jo, Y. G., & Lee, H. S. (2022). Dynamic rod worth measurement method based on eqilibrium -kinetics status. Nuclear Engineering and Technology, 54 (3), 781–789. https://doi.org/10.1016/j.net.2021.08.033
[16]	Riley, Tony. Calibration of Reactivity Oscillator for ISU-AGN-201 Reactor. Pocatello: Idaho State University (Thesis), 2011.
[17]	Study of the Open Loop and Closed Loop Oscillator Techniques. (n.d.).
[18]	Vidal-Ferràndiz, A., Ginestar, D., Carreño, A., Verdú, G., Dokhane, A., Verma, V., Perin, Y., Herb, J., Mylonakis, A., Demazière, C., & Vinai, P. (2022). Modelling and simulations of reactor neutron noise induced by mechanical vibrations. Annals of Nuclear Energy, 177. https://doi.org/10.1016/j.anucene.2022.109300
[19]	Vinai, P., Brighenti, A., Demazière, C., & Gasse, B. (n.d.). Development and comparison of highorder solvers for reactor noise analysis. http://cortex-h2020.eu
[20]	Vinai, P., Yi, H., Demazière, C., Rouchon, A., Zoia, A., Vidal-Ferràndiz, A., Carreño, A., Ginestar, D., & Verdú, G. (2023a). On the simulation of neutron noise induced by vibrations of fuel pins in a fuel assembly. Annals of Nuclear Energy, 181. https://doi.org/10.1016/j.anucene.2022.109521
[21]	Vinai, P., Yi, H., Demazière, C., Rouchon, A., Zoia, A., Vidal-Ferràndiz, A., Carreño, A., Ginestar, D., & Verdú, G. (2023b). On the simulation of neutron noise induced by vibrations of fuel pins in a fuel assembly. Annals of Nuclear Energy, 181. https://doi.org/10.1016/j.anucene.2022.109521
[22]	Yum, S., Hursin, M., Vasiliev, A., Vinai, P., Mylonakis, A. G., Demazière, C., & Macián-Juan, R. (2022). Uncertainty analyses of neutron noise simulations in a Zero-Power reactor. Annals of Nuclear Energy, 174. https://doi.org/10.1016/j.anucene.2022.109157

Cite This Article

Plain Text BibTeX RIS

APA Style

Harish Aryal. (2023). Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. American Journal of Science, Engineering and Technology, 8(2), 104-109. https://doi.org/10.11648/j.ajset.20230802.14

Copy | Download

ACS Style

Harish Aryal. Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. Am. J. Sci. Eng. Technol. 2023, 8(2), 104-109. doi: 10.11648/j.ajset.20230802.14

Copy | Download

AMA Style

Harish Aryal. Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. Am J Sci Eng Technol. 2023;8(2):104-109. doi: 10.11648/j.ajset.20230802.14

Copy | Download

@article{10.11648/j.ajset.20230802.14,
  author = {Harish Aryal},
  title = {Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems},
  journal = {American Journal of Science, Engineering and Technology},
  volume = {8},
  number = {2},
  pages = {104-109},
  doi = {10.11648/j.ajset.20230802.14},
  url = {https://doi.org/10.11648/j.ajset.20230802.14},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajset.20230802.14},
  abstract = {The project is about building an infrastructure for an open loop technique and implementing this technique to measure the reactivity worth of small samples. The reactivity samples are allowed to oscillate back and forth in the reactor system to cause perturbations and the corresponding reactor response is measured in the form of the transfer function. The transfer function obtained is used to determine stability characteristics along with other kinetic parameters such as delayed neutron fraction, prompt neutron lifetime, shutdown margins, and absolute power. This paper compares transfer functions for reactors like Neutron Radiography (NRAD) and Aerojet General Nuclear (AGN-201). The magnitude of the transfer function correlates with the reactivity of the sample that caused the perturbation. In addition, the transfer function allows one to determine whether the reactor is a stable system or not. In other words, the reactor’s response to the change in neutron population in the reactor can be easily described. Moreover, a transfer function measurement is useful to extract important kinetic parameters of the reactor system, such as instance prompt neutron generation lifetime, reactivity shutdown margin, absolute power, etc. The transfer function plots presented in the results section correlate the reactivity of the sample that caused perturbations. NRAD was found to have a higher break frequency than that AGN-201. This was an expected result since break frequency is inversely proportional to neutron generation time. With this relation, break frequency was found to be around 306 Hertz. So, the reactor cannot respond beyond this frequency but passes the low frequencies. The corresponding analysis and comparative transfer function plots using MATLAB for these two reactor systems are presented in the results section. Many reactivity measurements have been already in practice however if the transfer function technique can give reactivity measurements with similar or better precision and accuracy, it could be a great benefit. Moreover, this can be installed in those facilities where more complex systems cannot be incorporated easily.},
 year = {2023}
}

Copy | Download

TY  - JOUR
T1  - Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems
AU  - Harish Aryal
Y1  - 2023/05/31
PY  - 2023
N1  - https://doi.org/10.11648/j.ajset.20230802.14
DO  - 10.11648/j.ajset.20230802.14
T2  - American Journal of Science, Engineering and Technology
JF  - American Journal of Science, Engineering and Technology
JO  - American Journal of Science, Engineering and Technology
SP  - 104
EP  - 109
PB  - Science Publishing Group
SN  - 2578-8353
UR  - https://doi.org/10.11648/j.ajset.20230802.14
AB  - The project is about building an infrastructure for an open loop technique and implementing this technique to measure the reactivity worth of small samples. The reactivity samples are allowed to oscillate back and forth in the reactor system to cause perturbations and the corresponding reactor response is measured in the form of the transfer function. The transfer function obtained is used to determine stability characteristics along with other kinetic parameters such as delayed neutron fraction, prompt neutron lifetime, shutdown margins, and absolute power. This paper compares transfer functions for reactors like Neutron Radiography (NRAD) and Aerojet General Nuclear (AGN-201). The magnitude of the transfer function correlates with the reactivity of the sample that caused the perturbation. In addition, the transfer function allows one to determine whether the reactor is a stable system or not. In other words, the reactor’s response to the change in neutron population in the reactor can be easily described. Moreover, a transfer function measurement is useful to extract important kinetic parameters of the reactor system, such as instance prompt neutron generation lifetime, reactivity shutdown margin, absolute power, etc. The transfer function plots presented in the results section correlate the reactivity of the sample that caused perturbations. NRAD was found to have a higher break frequency than that AGN-201. This was an expected result since break frequency is inversely proportional to neutron generation time. With this relation, break frequency was found to be around 306 Hertz. So, the reactor cannot respond beyond this frequency but passes the low frequencies. The corresponding analysis and comparative transfer function plots using MATLAB for these two reactor systems are presented in the results section. Many reactivity measurements have been already in practice however if the transfer function technique can give reactivity measurements with similar or better precision and accuracy, it could be a great benefit. Moreover, this can be installed in those facilities where more complex systems cannot be incorporated easily.
VL  - 8
IS  - 2
ER  -

Copy | Download

Author Information

Harish Aryal

Mechanical Engineering, Marymount University, Arlington, The United States

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Harish Aryal. (2023). Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. American Journal of Science, Engineering and Technology, 8(2), 104-109. https://doi.org/10.11648/j.ajset.20230802.14

Copy | Download

ACS Style

Harish Aryal. Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. Am. J. Sci. Eng. Technol. 2023, 8(2), 104-109. doi: 10.11648/j.ajset.20230802.14

Copy | Download

AMA Style

Harish Aryal. Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems. Am J Sci Eng Technol. 2023;8(2):104-109. doi: 10.11648/j.ajset.20230802.14

Copy | Download

@article{10.11648/j.ajset.20230802.14,
  author = {Harish Aryal},
  title = {Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems},
  journal = {American Journal of Science, Engineering and Technology},
  volume = {8},
  number = {2},
  pages = {104-109},
  doi = {10.11648/j.ajset.20230802.14},
  url = {https://doi.org/10.11648/j.ajset.20230802.14},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajset.20230802.14},
  abstract = {The project is about building an infrastructure for an open loop technique and implementing this technique to measure the reactivity worth of small samples. The reactivity samples are allowed to oscillate back and forth in the reactor system to cause perturbations and the corresponding reactor response is measured in the form of the transfer function. The transfer function obtained is used to determine stability characteristics along with other kinetic parameters such as delayed neutron fraction, prompt neutron lifetime, shutdown margins, and absolute power. This paper compares transfer functions for reactors like Neutron Radiography (NRAD) and Aerojet General Nuclear (AGN-201). The magnitude of the transfer function correlates with the reactivity of the sample that caused the perturbation. In addition, the transfer function allows one to determine whether the reactor is a stable system or not. In other words, the reactor’s response to the change in neutron population in the reactor can be easily described. Moreover, a transfer function measurement is useful to extract important kinetic parameters of the reactor system, such as instance prompt neutron generation lifetime, reactivity shutdown margin, absolute power, etc. The transfer function plots presented in the results section correlate the reactivity of the sample that caused perturbations. NRAD was found to have a higher break frequency than that AGN-201. This was an expected result since break frequency is inversely proportional to neutron generation time. With this relation, break frequency was found to be around 306 Hertz. So, the reactor cannot respond beyond this frequency but passes the low frequencies. The corresponding analysis and comparative transfer function plots using MATLAB for these two reactor systems are presented in the results section. Many reactivity measurements have been already in practice however if the transfer function technique can give reactivity measurements with similar or better precision and accuracy, it could be a great benefit. Moreover, this can be installed in those facilities where more complex systems cannot be incorporated easily.},
 year = {2023}
}

Copy | Download

TY  - JOUR
T1  - Comparative Study of Transfer Functions for NRAD and AGN-201 Reactor Systems
AU  - Harish Aryal
Y1  - 2023/05/31
PY  - 2023
N1  - https://doi.org/10.11648/j.ajset.20230802.14
DO  - 10.11648/j.ajset.20230802.14
T2  - American Journal of Science, Engineering and Technology
JF  - American Journal of Science, Engineering and Technology
JO  - American Journal of Science, Engineering and Technology
SP  - 104
EP  - 109
PB  - Science Publishing Group
SN  - 2578-8353
UR  - https://doi.org/10.11648/j.ajset.20230802.14
AB  - The project is about building an infrastructure for an open loop technique and implementing this technique to measure the reactivity worth of small samples. The reactivity samples are allowed to oscillate back and forth in the reactor system to cause perturbations and the corresponding reactor response is measured in the form of the transfer function. The transfer function obtained is used to determine stability characteristics along with other kinetic parameters such as delayed neutron fraction, prompt neutron lifetime, shutdown margins, and absolute power. This paper compares transfer functions for reactors like Neutron Radiography (NRAD) and Aerojet General Nuclear (AGN-201). The magnitude of the transfer function correlates with the reactivity of the sample that caused the perturbation. In addition, the transfer function allows one to determine whether the reactor is a stable system or not. In other words, the reactor’s response to the change in neutron population in the reactor can be easily described. Moreover, a transfer function measurement is useful to extract important kinetic parameters of the reactor system, such as instance prompt neutron generation lifetime, reactivity shutdown margin, absolute power, etc. The transfer function plots presented in the results section correlate the reactivity of the sample that caused perturbations. NRAD was found to have a higher break frequency than that AGN-201. This was an expected result since break frequency is inversely proportional to neutron generation time. With this relation, break frequency was found to be around 306 Hertz. So, the reactor cannot respond beyond this frequency but passes the low frequencies. The corresponding analysis and comparative transfer function plots using MATLAB for these two reactor systems are presented in the results section. Many reactivity measurements have been already in practice however if the transfer function technique can give reactivity measurements with similar or better precision and accuracy, it could be a great benefit. Moreover, this can be installed in those facilities where more complex systems cannot be incorporated easily.
VL  - 8
IS  - 2
ER  -

Copy | Download