An experimental study performed to investigate the effect of nanofluid forced convection heat transfer and fluid flow characteristic. Three types of nanofluids {γAl2O3, CuO and ZrO2-DIW} flow under laminar or turbulent condition in inner pipe. The shear thinning behavior of blood is more accurately modeled by non-Newtonian Blood Mimic Fluids BMF. Here heat transfer and friction factor correlations developed for nonreactive Newtonian and non-Newtonian BMF fluids of (water: glycerol: xanthan gums) and heparinized bovine blood. The results show that the BMF Nussult number (Nub) increased as increasing Graetz number, and as flow index (n) decreasing. Bovine blood gives the temperatures distribution similar to (BMF6) but with lower Nusselt number by (31.2%). The BMF friction factor increases with decreasing (n), but the Bovine blood gives higher friction factor as compared with BMF6 by (25.6%). It was observed that all nanofluids types showed higher heat transfer characteristics than the base fluid DIW. It was also noted that in the γAl2O3 shows higher enhancement than the other by (82.4%) at (Renf =12670) and (ɸ=1 vol.% ). Comparisons present experimental results with previously reported results it gives good agreement.
| Published in | Engineering and Applied Sciences (Volume 2, Issue 1) |
| DOI | 10.11648/j.eas.20170201.11 |
| Page(s) | 1-16 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2024. Published by Science Publishing Group |
Non-newtonian Fluids, Nanofluids, Hypothermia, Intravenous Cooling
| [1] | Ratcliff, J. D., Frozen Sleep: New Frontier in Surgery, Readers Digest, September, p. 93, 2002. |
| [2] | Sjetil S., Therapeutic Hypothermia with Endovascular cooling, Ph. D., and Dept. Anesthesiology unlevel university hospital, Oslo, Norway Scand J Trauma ResuscEmerg Med, 12; 23-25, 2004. |
| [3] | Sebastien F., André B., Paulo R., Jean-A. G., Olivier S., (2011): "Hydraulic and heat transfer study of SiO2/water nanofluids in horizontal tubes with imposed wall temperature boundary conditions, "Universities Joseph Fourier, France Int. J. of Heat and Fluid Flow 32, 424–439. |
| [4] | Choi, U.S, (1998): " Nanofluid technology current status and future”, Second Korean-American Scientists and Engineers Association Research Technologies October 22- 24, Vienna, pp 2-21. |
| [5] | Zeinali Herisl, S. Gh. Etamad, M. Nasr Esfahani, (2006): "Heat Transfer Enhancement of Nanfluid Laminar Flow", Iran 14th Annual (Int.) Mechanical Engineering Conference, Isfahan University of Technology, Isfahan, Iran. |
| [6] | Anoop K., Sundararajan T., Sarit K. D., (2009): "Effect of particle size on the convective heat transfer in nanofluid in the developing region", Chennai India Int. J. of Heat and Mass Transfer 52, 2189–2195. |
| [7] | Zhang S., Zhong-yang, Chun-hui, Ming-jiang, (2009): "Heat Transfer Properties of CuO-water Nanofluids in Laminar Flow", Zhejiang University, Hangzhou Zhejiang Province, China, Chin. Soc. for Elec. Eng. Vol. 29 No. 32 Nov. 15. |
| [8] | Byung H. C., Hyun U. K., and Sung H. K., (2008): "Effect of alumina nanoparticles in the fluid on heat transfer in double-pipe heat exchanger system" Department of Chemical and Biological Engineering, Applied Rheology Center, Korea University, Seoul 136-701, Korea Korean J. Chem. Eng., 25 (5), 966-971. |
| [9] | Aghayari, R., Heydar Maddah, Malihe Zarei, Mehdi Dehghani, and Sahar Ghanbari Kaskari Mahalle, Heat Transfer of Nanofluid in a Double Pipe Heat Exchanger, International Scholarly Research Notices, Volume 2014 (2014), Article ID 736424, 7 pages. |
| [10] | Sudarmadji S., A New Correlation for Pressure Drop in, The Cooling Process of AL2O3-Water Nanofluid in Pipes, FME Transactions (2015) 43, 40-46. |
| [11] | Mohamed H. Shedid, M. M. Hassan, Numerical Investigation of Heat Transfer Characteristics for the Annular Flow of Nanofluids using YPlus, Journal of Fluid Flow, Heat and Mass Transfer, Volume 3, Year 2016. |
| [12] | Masoud H. F., Mohammad R. T., and Somaye N., (2011): "Numerical and Experimental Investigation OF Heat Transfer OF ZnO/Water Nan Fluid in the Concentric Tube And Plate Heat Exchangers", Canada, Numerical and Experimental Investigation of Thermal Science, Vol. 15, No. 1, pp. 183-194. |
| [13] | Bozorgan N., Mostafa M. and Nariman B., (2012): "Performance Evaluation of AI2O3/Water Nanofluid as Coolant in a Double-Tube Heat Exchanger Flowing under a Turbulent Flow Regime", Advances in Mechanical Engineering Volume, 8 pages. |
| [14] | MacDonald DA, Pulsatile flow in a catheterized artery, J. Biomech 9: 239–249, 1986. |
| [15] | Back LH, Estimated mean flow resistance increase during coronary artery catheterization, Biomech 27: 169–175, 1994. |
| [16] | Rao AR, Padmavathi K, Mathematical models for catheter movement in blood vessels, GAMS J Math Math Biosci 1: 57–78, 1997. |
| [17] | Back LH, Kwack EY, Back MR, Flow rate–pressure drop relation in coronary angioplasty: Catheter obstruction effect, Trans ASME J Biomech Eng 118: 83–89, 1996. |
| [18] | Dash RK, Jayaraman G, Mehta KN, Estimation of increased flow resistance in a narrow catheterized artery — A theoretical model, J. Biomech 29: 917–930, 1996. |
| [19] | Banerjee RK, Back LH, Back MR, Cho YI, Catheter obstruction effect on pulsatile flow rate–pressure drop during coronary angioplasty, Trans ASME J Biomech Eng 121: 281–289, 1999. |
| [20] | Jason L, Carter L, Greg M and Jennifer A, Modeling Therapeutic Hypothermia Using Heat Exchange Catheter to Cool Blood BEE 4530, Applications to Biomedical Systems. Cambridge, UK: Cambridge UP, Print. 2011. |
| [21] | Rajasekharan, S., V. G. Kubair, and N. R. Kuloor., Heat transfer to non- Newtonian fluids in coiled pipes in laminar flow, International Journal of Heat and Mass Transfer, Vol. 13: 1583-1594, 1990. |
| [22] | Hsu, C.-F., and S. V. Patankar., Analysis of laminar non-Newtonian flow and heat transfer in curved tubes, AIChE Journal, Vol. 28 (4): 610-616. 1982. |
| [23] | Rao, B. K., "Turbulent heat transfer to power-law fluids in helical passages., International Journal of Heat and Fluid Flow, Vol. 15 (2): 142-148. 1994. |
| [24] | Escudier, P. J. Oliveira, F. T. Pinho, S. Smith, Fully developed laminar flow of non-Newtonian liquids through annuli: comparison of numerical calculations with experiments, Experiments in Fluids 33, s00348-002-0429-4., 2002. |
| [25] | Lain William Gouldson, The Flow of Newtonian and Non-Newtonian Fluids in an Annular Geometry, Ph. D. Thesis, University of Liverpool by February, 1997. |
| [26] | Wickramasinghe, B. Han, C. M. Kahr., Designing Blood Oxygenators using Blood Mimic Fluids, Department of Chemical Engineering, Colorado State University, Fort Collins, CO, 80523-1370, USA, 2004. |
| [27] | Wickramasinghe S. and Han B., Designing Micro porous Hollow Fiber Blood Oxygenators, Chemical Engineering Research and Design, 83 (A3): 256–267., 2005. |
| [28] | Chhabra R. P. and Richardson J. F., Non-Newtonian Flow in the Process Industries, Fundamentals and Engineering Applications Department of Chemical and Biological Process Engineering, University of Wales, Swansea SA2 8PP, Great Britain, 1999. |
| [29] | Bird, R. B., Armstrong, R. C. and Hassager, O., Dynamics of Polymeric Liquids,. Vol. 1 Fluid Dynamics, 2nd edn. Wiley, New York, 1997. |
| [30] | Wickramasinghe, S. R., Garcia, J. D. and Han, B., 2002a, Mass and momentum transfer in hollow fiber blood oxygenators, J Membr Sci, 208: 247. |
| [31] | Yuejin Luo, Non-Newtonian Annular Flow and Cuttings Transport through Drilling Annuli at Various Angles, Ph. D. thesis, Department of Petroleum Engineering Heriot-Watt University Edinburgh, U.K. October, 1988. |
| [32] | Sébastien Ferrouillat, André Bontemps a, J. Paulo Ribeiro b, Jean-Antoine Gruss b, Olivier Soriano "Hydraulic and heat transfer study of SiO2/water nanofluids in horizontal tubes with imposed wall temperature boundary conditions"International Journal of Heat and Fluid Flow 32 (2011) 424–439. |
| [33] | Leveque, J., Ann. Mines. 13, 1928, 201, 305, 381. |
APA Style
Abdulhassan Abed Karamallah, Kadhum Audaa Jehhef. (2017). Application of Nanofluids for Cooling Newtonian and Non-Newtonian Blood Mimicking Fluids Flow in Annular Space. Engineering and Applied Sciences, 2(1), 1-16. https://doi.org/10.11648/j.eas.20170201.11
ACS Style
Abdulhassan Abed Karamallah; Kadhum Audaa Jehhef. Application of Nanofluids for Cooling Newtonian and Non-Newtonian Blood Mimicking Fluids Flow in Annular Space. Eng. Appl. Sci. 2017, 2(1), 1-16. doi: 10.11648/j.eas.20170201.11
AMA Style
Abdulhassan Abed Karamallah, Kadhum Audaa Jehhef. Application of Nanofluids for Cooling Newtonian and Non-Newtonian Blood Mimicking Fluids Flow in Annular Space. Eng Appl Sci. 2017;2(1):1-16. doi: 10.11648/j.eas.20170201.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.eas.20170201.11,
author = {Abdulhassan Abed Karamallah and Kadhum Audaa Jehhef},
title = {Application of Nanofluids for Cooling Newtonian and Non-Newtonian Blood Mimicking Fluids Flow in Annular Space},
journal = {Engineering and Applied Sciences},
volume = {2},
number = {1},
pages = {1-16},
doi = {10.11648/j.eas.20170201.11},
url = {https://doi.org/10.11648/j.eas.20170201.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.eas.20170201.11},
abstract = {An experimental study performed to investigate the effect of nanofluid forced convection heat transfer and fluid flow characteristic. Three types of nanofluids {γAl2O3, CuO and ZrO2-DIW} flow under laminar or turbulent condition in inner pipe. The shear thinning behavior of blood is more accurately modeled by non-Newtonian Blood Mimic Fluids BMF. Here heat transfer and friction factor correlations developed for nonreactive Newtonian and non-Newtonian BMF fluids of (water: glycerol: xanthan gums) and heparinized bovine blood. The results show that the BMF Nussult number (Nub) increased as increasing Graetz number, and as flow index (n) decreasing. Bovine blood gives the temperatures distribution similar to (BMF6) but with lower Nusselt number by (31.2%). The BMF friction factor increases with decreasing (n), but the Bovine blood gives higher friction factor as compared with BMF6 by (25.6%). It was observed that all nanofluids types showed higher heat transfer characteristics than the base fluid DIW. It was also noted that in the γAl2O3 shows higher enhancement than the other by (82.4%) at (Renf =12670) and (ɸ=1 vol.% ). Comparisons present experimental results with previously reported results it gives good agreement.},
year = {2017}
}
TY - JOUR
T1 - Application of Nanofluids for Cooling Newtonian and Non-Newtonian Blood Mimicking Fluids Flow in Annular Space
AU - Abdulhassan Abed Karamallah
AU - Kadhum Audaa Jehhef
Y1 - 2017/03/04
PY - 2017
N1 - https://doi.org/10.11648/j.eas.20170201.11
DO - 10.11648/j.eas.20170201.11
T2 - Engineering and Applied Sciences
JF - Engineering and Applied Sciences
JO - Engineering and Applied Sciences
SP - 1
EP - 16
PB - Science Publishing Group
SN - 2575-1468
UR - https://doi.org/10.11648/j.eas.20170201.11
AB - An experimental study performed to investigate the effect of nanofluid forced convection heat transfer and fluid flow characteristic. Three types of nanofluids {γAl2O3, CuO and ZrO2-DIW} flow under laminar or turbulent condition in inner pipe. The shear thinning behavior of blood is more accurately modeled by non-Newtonian Blood Mimic Fluids BMF. Here heat transfer and friction factor correlations developed for nonreactive Newtonian and non-Newtonian BMF fluids of (water: glycerol: xanthan gums) and heparinized bovine blood. The results show that the BMF Nussult number (Nub) increased as increasing Graetz number, and as flow index (n) decreasing. Bovine blood gives the temperatures distribution similar to (BMF6) but with lower Nusselt number by (31.2%). The BMF friction factor increases with decreasing (n), but the Bovine blood gives higher friction factor as compared with BMF6 by (25.6%). It was observed that all nanofluids types showed higher heat transfer characteristics than the base fluid DIW. It was also noted that in the γAl2O3 shows higher enhancement than the other by (82.4%) at (Renf =12670) and (ɸ=1 vol.% ). Comparisons present experimental results with previously reported results it gives good agreement.
VL - 2
IS - 1
ER -
Information
Email: