The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose

Harry Budiharjo Sulistyarso; Joko Pamungkas; Yulius Deddy Hermawan

doi:doi:10.11648/j.pse.20220602.13

| Peer-Reviewed

The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose

Harry Budiharjo Sulistyarso, Joko Pamungkas, Yulius Deddy Hermawan

Published in Petroleum Science and Engineering (Volume 6, Issue 2)

Received: 19 October 2022 Accepted: 10 November 2022 Published: 23 November 2022

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Surfactant injection is one of Chemical EOR methods by injecting a special substance as a surface-active agent (surfactant). The purpose is to reduce the interfacial tension (IFT) and the viscosity value of crude oil. This research was conducted to analyze the effect of adding anionic surfactant sodium lignosulfonate (SLS) on a laboratory scale. The sample of crude oil samples are obtained from Wonocolo field, Indonesia. The surfactant was obtained by almond peel extraction, developed at Laboratory Research EOR University of Pembangunan National "Veteran" Yogyakarta. SLS compositions for the experiment are 2%, 4%, 6% and 8% v/v. The test was made at 30, 40, 50, 60 and 70°C. The results showed that 6% v/v SLS solution was the best composition to significantly reduce IFT at 70°C from 32.78 mN/m to 3.22 mN/m. This composition also being the value of critical micelle concentration (CMC) for SLS. At above critical micelle concentration, the additional of surfactants will be insignificant on IFT reduction and also excess amount of surfactant in aqueous solution. With SLS 8% v/v solution gain the lowest viscosity of the fluid from 2.54 cP to 1.88 cP. In addition, the results of this study showed that when the reduction in IFT was the highest, the viscosity reduction was the highest.

Published in	Petroleum Science and Engineering (Volume 6, Issue 2)
DOI	10.11648/j.pse.20220602.13
Page(s)	59-64
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2022. Published by Science Publishing Group

Keywords

Crude Oil, Enhanced Oil Recovery, Interfacial Tension, Surfactant SLS, Viscosity

References

[1]	Karatayev, M., Movkebayeva, G., Bimagambetova, Z., (2019). “In: Mouraviev, N, Koulouri, A. (Eds.), Increasing Utilisation of Renewable Energy Sources: Comparative Analysis of Scenarios Until 2050 BT - Energy Security: Policy Challenges and Solutions for Resource Efficiency”. Springer International Publishing, Cham, pp. 57.
[2]	Joshi, S. J., Geetha, S. J., Desai, A. J., (2015). “Characterization and application of bio-surfactant produced by bacillus licheniformis R2”. Appl. Biochem. Biotechnol. 177, pp. 351-352.
[3]	Höök, M., Davidsson, S., Johansson, S., Tang, X., (2014). “Decline and depletion rates of oil production: A comprehensive investigation”. Philos. Trans. R. Soc. Lond. Ser. A Math. Phys. Eng. Sci. 372, 20120448, pp. 4.
[4]	Haq, B., Liu, J., Liu, K., Al Shehri, D., (2020). “The role of biodegradable surfactant in microbial enhanced oil recovery”. J. Petrol. Sci. Eng. 189, 106688, pp. 1-2.
[5]	Blunt, M., Fayers, F. J., Orr, F. M., (1993). “Carbon dioxide in enhanced oil recovery”. Energy Convers. Manag. 34, pp. 1199–1200.
[6]	Zulkifli, N. N., Mahmood, S. M., Akbari, S., Manap, A. A. A., Kechut, N. I., Elrais, K. A., (2020). “Evaluation of new surfactants for enhanced oil recovery applications in high-temperature reservoirs”. J. Pet. Explor. Prod. Technol. 10, pp. 283, 295.
[7]	Viades-Trejo, J., & Gracia-Fadrique, J., (2007). “Spinning drop method. From Young-Laplace to Vonnegut”. Colloids and Surfaces A: Physicochemical and Engineering Aspects. 302, pp. 550.
[8]	Sun, N. N., J. Q. Jing, Y. Ding, X. X. Zang, and L. Zou., (2015). “Effects of cationic/anionic electrolytes on the stability of viscous crude oil-in-water emulsions”. Chemical Industry and Engineering Progress 34 (8), pp. 3119, 3121-3122.
[9]	Liu, Z., Hedayati, P., Sudhölter, E. J. R., Haaring, R., Shaik, A. R., Kumar, N., (2020). “Adsorption behavior of anionic surfactants to silica surfaces in the presence of calcium ion and polystyrene sulfonate”. Colloids Surf. A 602, 125074, pp. 9, 23.
[10]	Hart, A., (2014). “A review of technologies for transporting viscous crude oil and bitumen via pipelines”. Journal of Petroleum Exploration and Production Technology 4 (3), pp. 331.
[11]	Zaki. N. N. Ahmed. N. S. & Nassar. A. M., (2000). “Sodium lignin sulfonate to stabilize heavy crude oil-in-water emulsions for pipeline transportation”. Petroleum Science and Technology. 18 (9–10), pp. 1179, 1183-1186.
[12]	S. Priyanto et al., (2021). “Synthesis of Sodium Ligno Sulfonate (SLS) Surfactant from Black Liquor Waste and The Potential Test for EOR in Ledok Field Cepu”. IOP Conf. Ser. Mater. Sci. Eng., vol. 1053, no. 1, pp. 012075.
[13]	Sulistyarso, H. B., Pamungkas, J., Gusmarwani, S. R., Widyaningsih, I., & Perwira, K. Y., (2021). “Field Test of U-Champ Biosurfactant in Oil Spill Bioremediation”. International Journal of Recent Technology and Engineering (IJRTE)”. 10 (3), pp 76.
[14]	Liu, M., Wu, Y., Zhang, L., Rong, F., & Yang, Z., (2018). “Mechanism of viscosity reduction in viscous crude oil with polyoxyethylene surfactant compound system”. Petroleum Science and Technology, 37 (4), pp. 410.
[15]	M. M. Azis et al., (2021). “Development of ultralow interfacial tension lignosulfonate from kraft black liquor for enhanced oil recovery”, J. Eng. Technol. Sci., vol. 53, no. 2, pp. 330, 335.

Cite This Article

Plain Text BibTeX RIS

APA Style

Harry Budiharjo Sulistyarso, Joko Pamungkas, Yulius Deddy Hermawan. (2022). The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Petroleum Science and Engineering, 6(2), 59-64. https://doi.org/10.11648/j.pse.20220602.13

Copy | Download

ACS Style

Harry Budiharjo Sulistyarso; Joko Pamungkas; Yulius Deddy Hermawan. The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Pet. Sci. Eng. 2022, 6(2), 59-64. doi: 10.11648/j.pse.20220602.13

Copy | Download

AMA Style

Harry Budiharjo Sulistyarso, Joko Pamungkas, Yulius Deddy Hermawan. The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Pet Sci Eng. 2022;6(2):59-64. doi: 10.11648/j.pse.20220602.13

Copy | Download

@article{10.11648/j.pse.20220602.13,
  author = {Harry Budiharjo Sulistyarso and Joko Pamungkas and Yulius Deddy Hermawan},
  title = {The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose},
  journal = {Petroleum Science and Engineering},
  volume = {6},
  number = {2},
  pages = {59-64},
  doi = {10.11648/j.pse.20220602.13},
  url = {https://doi.org/10.11648/j.pse.20220602.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.pse.20220602.13},
  abstract = {Surfactant injection is one of Chemical EOR methods by injecting a special substance as a surface-active agent (surfactant). The purpose is to reduce the interfacial tension (IFT) and the viscosity value of crude oil. This research was conducted to analyze the effect of adding anionic surfactant sodium lignosulfonate (SLS) on a laboratory scale. The sample of crude oil samples are obtained from Wonocolo field, Indonesia. The surfactant was obtained by almond peel extraction, developed at Laboratory Research EOR University of Pembangunan National "Veteran" Yogyakarta. SLS compositions for the experiment are 2%, 4%, 6% and 8% v/v. The test was made at 30, 40, 50, 60 and 70°C. The results showed that 6% v/v SLS solution was the best composition to significantly reduce IFT at 70°C from 32.78 mN/m to 3.22 mN/m. This composition also being the value of critical micelle concentration (CMC) for SLS. At above critical micelle concentration, the additional of surfactants will be insignificant on IFT reduction and also excess amount of surfactant in aqueous solution. With SLS 8% v/v solution gain the lowest viscosity of the fluid from 2.54 cP to 1.88 cP. In addition, the results of this study showed that when the reduction in IFT was the highest, the viscosity reduction was the highest.},
 year = {2022}
}

Copy | Download

TY - JOUR
T1 - The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose
AU - Harry Budiharjo Sulistyarso
AU - Joko Pamungkas
AU - Yulius Deddy Hermawan
Y1 - 2022/11/23
PY - 2022
N1 - https://doi.org/10.11648/j.pse.20220602.13
DO - 10.11648/j.pse.20220602.13
T2 - Petroleum Science and Engineering
JF - Petroleum Science and Engineering
JO - Petroleum Science and Engineering
SP - 59
EP - 64
PB - Science Publishing Group
SN - 2640-4516
UR - https://doi.org/10.11648/j.pse.20220602.13
AB - Surfactant injection is one of Chemical EOR methods by injecting a special substance as a surface-active agent (surfactant). The purpose is to reduce the interfacial tension (IFT) and the viscosity value of crude oil. This research was conducted to analyze the effect of adding anionic surfactant sodium lignosulfonate (SLS) on a laboratory scale. The sample of crude oil samples are obtained from Wonocolo field, Indonesia. The surfactant was obtained by almond peel extraction, developed at Laboratory Research EOR University of Pembangunan National "Veteran" Yogyakarta. SLS compositions for the experiment are 2%, 4%, 6% and 8% v/v. The test was made at 30, 40, 50, 60 and 70°C. The results showed that 6% v/v SLS solution was the best composition to significantly reduce IFT at 70°C from 32.78 mN/m to 3.22 mN/m. This composition also being the value of critical micelle concentration (CMC) for SLS. At above critical micelle concentration, the additional of surfactants will be insignificant on IFT reduction and also excess amount of surfactant in aqueous solution. With SLS 8% v/v solution gain the lowest viscosity of the fluid from 2.54 cP to 1.88 cP. In addition, the results of this study showed that when the reduction in IFT was the highest, the viscosity reduction was the highest.
VL - 6
IS - 2
ER -

Copy | Download

Author Information

Harry Budiharjo Sulistyarso

Department of Petroleum Engineering, Faculty of Mineral Technology, UPN “Veteran”, Yogyakarta, Indonesia
Joko Pamungkas

Department of Petroleum Engineering, Faculty of Mineral Technology, UPN “Veteran”, Yogyakarta, Indonesia
Yulius Deddy Hermawan

Department of Chemical Engineering, Faculty of Industrial and Technology, UPN “Veteran”, Yogyakarta, Indonesia

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Harry Budiharjo Sulistyarso, Joko Pamungkas, Yulius Deddy Hermawan. (2022). The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Petroleum Science and Engineering, 6(2), 59-64. https://doi.org/10.11648/j.pse.20220602.13

Copy | Download

ACS Style

Harry Budiharjo Sulistyarso; Joko Pamungkas; Yulius Deddy Hermawan. The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Pet. Sci. Eng. 2022, 6(2), 59-64. doi: 10.11648/j.pse.20220602.13

Copy | Download

AMA Style

Harry Budiharjo Sulistyarso, Joko Pamungkas, Yulius Deddy Hermawan. The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose. Pet Sci Eng. 2022;6(2):59-64. doi: 10.11648/j.pse.20220602.13

Copy | Download

@article{10.11648/j.pse.20220602.13,
  author = {Harry Budiharjo Sulistyarso and Joko Pamungkas and Yulius Deddy Hermawan},
  title = {The Effects Between Interfacial Tension and Viscosity Reduction in Viscous Crude Oil Through the Addition of Surfactant Sodium Lignosulfonate (SLS) for EOR Purpose},
  journal = {Petroleum Science and Engineering},
  volume = {6},
  number = {2},
  pages = {59-64},
  doi = {10.11648/j.pse.20220602.13},
  url = {https://doi.org/10.11648/j.pse.20220602.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.pse.20220602.13},
  abstract = {Surfactant injection is one of Chemical EOR methods by injecting a special substance as a surface-active agent (surfactant). The purpose is to reduce the interfacial tension (IFT) and the viscosity value of crude oil. This research was conducted to analyze the effect of adding anionic surfactant sodium lignosulfonate (SLS) on a laboratory scale. The sample of crude oil samples are obtained from Wonocolo field, Indonesia. The surfactant was obtained by almond peel extraction, developed at Laboratory Research EOR University of Pembangunan National "Veteran" Yogyakarta. SLS compositions for the experiment are 2%, 4%, 6% and 8% v/v. The test was made at 30, 40, 50, 60 and 70°C. The results showed that 6% v/v SLS solution was the best composition to significantly reduce IFT at 70°C from 32.78 mN/m to 3.22 mN/m. This composition also being the value of critical micelle concentration (CMC) for SLS. At above critical micelle concentration, the additional of surfactants will be insignificant on IFT reduction and also excess amount of surfactant in aqueous solution. With SLS 8% v/v solution gain the lowest viscosity of the fluid from 2.54 cP to 1.88 cP. In addition, the results of this study showed that when the reduction in IFT was the highest, the viscosity reduction was the highest.},
 year = {2022}
}

Copy | Download